How to bend metal fuel line
- Eugene
- Carburettor
- Posts: 1794
- Joined: Mon Jan 22, 2007 9:30 am
- What model do you have?: 2 many 2 mention :-)
- Location: Brackenfell
- Has thanked: 59 times
- Been thanked: 65 times
How to bend metal fuel line
So guys, how is this done correctly without stuffing up or pinching the pipe?
You can never have enough Garages
- fig
- Bus Driver
- Posts: 12214
- Joined: Fri Jan 20, 2006 10:08 pm
- What model do you have?: Type 2
- Facebook: https://www.facebook.com/groups/258896479219/
- Location: Where life is cheap and death is free
- Has thanked: 287 times
- Been thanked: 321 times
- Contact:
Re: How to bend metal fuel line
I just do it by hand. Carefully.
So long as you gently massage the bend and don't make the turns too tight, there's no need for special tools. Same applies to brake lines.
So long as you gently massage the bend and don't make the turns too tight, there's no need for special tools. Same applies to brake lines.
fig
Kaapse Kombi Kult
"Whether you think you can or whether you think you can't, you're right." -- Henry Ford
Kaapse Kombi Kult
"Whether you think you can or whether you think you can't, you're right." -- Henry Ford
-
- Fuel Injection
- Posts: 2005
- Joined: Mon Jul 16, 2012 5:56 pm
- What model do you have?: T3,1beetle
- Location: Kempton Park
- Has thanked: 193 times
- Been thanked: 121 times
Re: How to bend metal fuel line
Adendorff sell a small hand tube bender for about R150 if you need tighter bends but like Fig says by hand if they are bigger radius bends.
- Donovan D
- Donor
- Posts: 2229
- Joined: Sun Jun 01, 2008 6:27 pm
- What model do you have?: 67 Panel
- Facebook: http://www.facebook.com/profile.php?id=536371512
- Location: Brackenfell
- Has thanked: 148 times
- Been thanked: 73 times
- Tony Z
- Donor
- Posts: 14994
- Joined: Wed Sep 14, 2005 8:33 am
- What model do you have?: 2.3L 69; 1302; P/Van
- Location: Klipheuwel (near Durbanville), Cape Town or working at sea
- Has thanked: 191 times
- Been thanked: 487 times
Re: How to bend metal fuel line
plumbing benders also work
ANGRRR
http://www.aircooledvwsa.co.za/viewtopi ... 23&t=14775
1302S
http://www.aircooledvwsa.co.za/viewtopi ... 23&t=33521
Panel Van
http://www.aircooledvwsa.co.za/viewtopic.php?p=288723
http://www.aircooledvwsa.co.za/viewtopi ... 23&t=14775
1302S
http://www.aircooledvwsa.co.za/viewtopi ... 23&t=33521
Panel Van
http://www.aircooledvwsa.co.za/viewtopic.php?p=288723
vader wrote: The Force is strong with you young Sith Lord Z!
- retrovan
- Donor
- Posts: 8709
- Joined: Mon Feb 07, 2011 8:51 pm
- What model do you have?: 52T1,68FB,72Bay,75FL
- Location: Eich! no, in Jefferys Bay
- Has thanked: 421 times
- Been thanked: 539 times
- Contact:
Re: How to bend metal fuel line
Old Toppies always said...
You bend over the thigh not the hand, and you will never kink the pipe.
Herman
You bend over the thigh not the hand, and you will never kink the pipe.
Herman
1952 Split Beetle 1835cc
1968 Fastback 2Lt.type4
1972 Low Light Bay Panel Van 2Lt type 4
1975 Fleetline Panel Van 1914cc
2020 MeFusco Beetle Truck 2Lt type 4
1972 FT Hahn SP 1776 cc
1968 Fastback 2Lt.type4
1972 Low Light Bay Panel Van 2Lt type 4
1975 Fleetline Panel Van 1914cc
2020 MeFusco Beetle Truck 2Lt type 4
1972 FT Hahn SP 1776 cc