hoover plate
-
- Oil Pump
- Posts: 280
- Joined: Thu Apr 20, 2017 4:36 am
- What model do you have?: 1976 bay window
- Location: Roodeport
- Has thanked: 51 times
- Been thanked: 7 times
-
- Oil Pump
- Posts: 280
- Joined: Thu Apr 20, 2017 4:36 am
- What model do you have?: 1976 bay window
- Location: Roodeport
- Has thanked: 51 times
- Been thanked: 7 times
- fourier
- Oil Cooler
- Posts: 342
- Joined: Fri Sep 26, 2008 1:21 pm
- What model do you have?: '59 Ghia, '77 Beetle
- Location: Melkbosstrand, Cape Town
- Has thanked: 31 times
- Been thanked: 37 times
Re: hoover plate
Air will bypass the oil cooler, so don't run without it. It is like every other piece of engine tin on an aircooled VW... important to ensure proper cooling.
(o= i =o) (o\ ! /o)
- retrovan
- Donor
- Posts: 8709
- Joined: Mon Feb 07, 2011 8:51 pm
- What model do you have?: 52T1,68FB,72Bay,75FL
- Location: Eich! no, in Jefferys Bay
- Has thanked: 421 times
- Been thanked: 539 times
- Contact:
Re: hoover plate
To be found on your oil cooler.
Herman
1952 Split Beetle 1835cc
1968 Fastback 2Lt.type4
1972 Low Light Bay Panel Van 2Lt type 4
1975 Fleetline Panel Van 1914cc
2020 MeFusco Beetle Truck 2Lt type 4
1972 FT Hahn SP 1776 cc
1968 Fastback 2Lt.type4
1972 Low Light Bay Panel Van 2Lt type 4
1975 Fleetline Panel Van 1914cc
2020 MeFusco Beetle Truck 2Lt type 4
1972 FT Hahn SP 1776 cc
-
- Camshaft
- Posts: 893
- Joined: Wed Apr 20, 2016 7:10 pm
- What model do you have?: 1960 ghia
- Location: Nelson Mandela Metro
- Has thanked: 1 time
- Been thanked: 107 times
Re: hoover plate
Thanks Herman,....never seen it before !!
Will keep an open mind when fiddling in that area again,....and when scouring in scrap yards !!
Never ever seen it !
Haans
Will keep an open mind when fiddling in that area again,....and when scouring in scrap yards !!
Never ever seen it !
Haans
-
- Oil Pump
- Posts: 280
- Joined: Thu Apr 20, 2017 4:36 am
- What model do you have?: 1976 bay window
- Location: Roodeport
- Has thanked: 51 times
- Been thanked: 7 times
Re: hoover plate
Silly question ,if not fitted and motor is in can you seal that area externally with dynamat
- retrovan
- Donor
- Posts: 8709
- Joined: Mon Feb 07, 2011 8:51 pm
- What model do you have?: 52T1,68FB,72Bay,75FL
- Location: Eich! no, in Jefferys Bay
- Has thanked: 421 times
- Been thanked: 539 times
- Contact:
Re: hoover plate
I normally fill tin holes with aluminum duct tape, and spray it black.
That should work till the engine comes out at a later stage.
Herman
That should work till the engine comes out at a later stage.
Herman
1952 Split Beetle 1835cc
1968 Fastback 2Lt.type4
1972 Low Light Bay Panel Van 2Lt type 4
1975 Fleetline Panel Van 1914cc
2020 MeFusco Beetle Truck 2Lt type 4
1972 FT Hahn SP 1776 cc
1968 Fastback 2Lt.type4
1972 Low Light Bay Panel Van 2Lt type 4
1975 Fleetline Panel Van 1914cc
2020 MeFusco Beetle Truck 2Lt type 4
1972 FT Hahn SP 1776 cc
- fig
- Bus Driver
- Posts: 12214
- Joined: Fri Jan 20, 2006 10:08 pm
- What model do you have?: Type 2
- Facebook: https://www.facebook.com/groups/258896479219/
- Location: Where life is cheap and death is free
- Has thanked: 287 times
- Been thanked: 321 times
- Contact:
Re: hoover plate
I also replace the narrow strip of foam that goes over the oil cooler with thicker foam the full width of the cooler, which helps seal some of the gaps covered by the "Hoover bit".
The "Hoover bit" is hard to find and most of the ones I've found were cracked. Because the fanhousing screws onto it, I think many of them were damaged when people forced the fanhousing when it was still screwed to the Hoover bit.
FYI, since I know some people are asking by now, this part is called the "Hoover bit" from the Sermons of Bob Hoover, a series of mechanical lessons for ACVW mechanics written by the late Bob Hoover, who was one of the first people to note the importance of this tiny (usually missing) part.
fig
Kaapse Kombi Kult
"Whether you think you can or whether you think you can't, you're right." -- Henry Ford
Kaapse Kombi Kult
"Whether you think you can or whether you think you can't, you're right." -- Henry Ford
- Tony Z
- Donor
- Posts: 14994
- Joined: Wed Sep 14, 2005 8:33 am
- What model do you have?: 2.3L 69; 1302; P/Van
- Location: Klipheuwel (near Durbanville), Cape Town or working at sea
- Has thanked: 191 times
- Been thanked: 487 times
Re: hoover plate
If anyone is interested, I have a few new hoover bits as well as a few pairs of the lower tin (rear plate that goes below the cylinder covers) that I am happy to part with.
ANGRRR
http://www.aircooledvwsa.co.za/viewtopi ... 23&t=14775
1302S
http://www.aircooledvwsa.co.za/viewtopi ... 23&t=33521
Panel Van
http://www.aircooledvwsa.co.za/viewtopic.php?p=288723
http://www.aircooledvwsa.co.za/viewtopi ... 23&t=14775
1302S
http://www.aircooledvwsa.co.za/viewtopi ... 23&t=33521
Panel Van
http://www.aircooledvwsa.co.za/viewtopic.php?p=288723
vader wrote: The Force is strong with you young Sith Lord Z!