1962 T1 resto cal project
-
- Oil Pump
- Posts: 210
- Joined: Tue Jun 30, 2015 8:05 pm
- What model do you have?: 62
- Location: Pretoria
- Has thanked: 8 times
- Been thanked: 14 times
Re: 1962 T1 resto cal project
With my car still at the paint shop and crankcase at Bruce's place i was getting a little frustrated about not being able to do anything so i decided to refurbish my speedometer so long, nice little project.
It wasn't looking toi bad but when i tried to turn it with a piece of the old speedo cable it wouldn't budge. Tried all kinds of penetrating fluid and i didn't want to force it but no luck. I'll have ti open it up.
It wasn't looking toi bad but when i tried to turn it with a piece of the old speedo cable it wouldn't budge. Tried all kinds of penetrating fluid and i didn't want to force it but no luck. I'll have ti open it up.
-
- Oil Pump
- Posts: 210
- Joined: Tue Jun 30, 2015 8:05 pm
- What model do you have?: 62
- Location: Pretoria
- Has thanked: 8 times
- Been thanked: 14 times
Re: 1962 T1 resto cal project
I opened it up cleaned and polished the stainless steel bezel and surpirising enough the rubber seals were in perfect condition and not perished at all
Since this will be a total restoration and new motor i went ahead and rolled back the odometer
When i opened the magnetic cup i found the old grease was rock hard and that's why it wouldn't turn over.
With everything cleaned up i replaced the indicatir and warning light gels and cleaned ip the case a little, it was a bit tricky to get the little needle back into its brass bushing but she came out nice.
Since this will be a total restoration and new motor i went ahead and rolled back the odometer
When i opened the magnetic cup i found the old grease was rock hard and that's why it wouldn't turn over.
With everything cleaned up i replaced the indicatir and warning light gels and cleaned ip the case a little, it was a bit tricky to get the little needle back into its brass bushing but she came out nice.
- acpaterson
- Carburettor
- Posts: 1960
- Joined: Sat Jan 05, 2013 6:50 pm
- What model do you have?: Winston, a 74 Bay
- Location: Parklands, Cape Town
- Has thanked: 80 times
- Been thanked: 131 times
- Contact:
- jolas
- Donor
- Posts: 4253
- Joined: Fri Jul 16, 2010 10:11 am
- What model do you have?: '65 Kombi
- Location: Klapmuts, Western Cape
- Has thanked: 393 times
- Been thanked: 173 times
Re: 1962 T1 resto cal project
looks brand new !!!
by fig » Mar 26, 2018
Sambas in South Africa are good for only 2 things: showing off and sunburn.
Sambas in South Africa are good for only 2 things: showing off and sunburn.
- riaanj
- Exhaust Pipe
- Posts: 1665
- Joined: Wed Oct 06, 2010 8:17 pm
- What model do you have?: None ATM, oneday...
- Location: Germiston
- Has thanked: 6 times
- Been thanked: 41 times
Re: 1962 T1 resto cal project
Came out awesome, looks brand new!
Just keep on BUGGIN'
Protect the endangered, say NO to exporting our AirCooled spares & cars..
T6 Ranger 2.2TDCi D/Cab
307E Anglia panel-van
Honda CBR600RR
Honda CBR600F4
Honda CBR1100XX SuperBlackbird
Protect the endangered, say NO to exporting our AirCooled spares & cars..
T6 Ranger 2.2TDCi D/Cab
307E Anglia panel-van
Honda CBR600RR
Honda CBR600F4
Honda CBR1100XX SuperBlackbird
-
- Oil Pump
- Posts: 210
- Joined: Tue Jun 30, 2015 8:05 pm
- What model do you have?: 62
- Location: Pretoria
- Has thanked: 8 times
- Been thanked: 14 times
Re: 1962 T1 resto cal project
Okay so I'll post a few pics. I started off by building some wooden beams that i can rest the shell on, allowing me to get good access to the pan and front suspension without wasting too much space.
-
- Oil Pump
- Posts: 210
- Joined: Tue Jun 30, 2015 8:05 pm
- What model do you have?: 62
- Location: Pretoria
- Has thanked: 8 times
- Been thanked: 14 times
Re: 1962 T1 resto cal project
The original tank looked like a siv, managed to find one right here on ACVWSA, not 100%, had some dings and dents but all importantly, no rust. Stripped old paint and had a friend braze on a fuel return bung. It then got dipped in Chemloch rust remover and i finished the inside if the tank with an epoxy based tank sealer i got from Henry Kinnear, same stuff they used to seal inside of aircraft wet tanks. Then came a nice shiny gloss black.